How to

Delphi' Brake Discs. Our Own Discography.

Share Resource:

Resource Highlights

Like every good performer, we have our own collection of top selling discs. From cross drilled to vented, and high-carbon to coated. We think of it as our own ‘discography’…but for cars instead of your ears.

Tech spec resource banner
Braking Discs & Drums Technical specification 3 min read

Since every car is different, and every driver is different, what is right for one, might not work quite as well for the other. And vice versa. That’s why our engineers consider many variables when developing a new brake disc, based on the application, its intended use, driver preference and a plethora of other technical requirements. The result; a range of different disc castings and/or configurations, each with their own characteristics and, critically, each designed to perform just like the OE...

Vented discs: Since brake discs absorb significant amounts of thermal energy, it’s critical that this heat is controlled effectively. Whereas solid discs rely on ambient air to do this, our vented discs feature special internal cooling passages to maximise airflow. By continually moving air across the disc’s surface or through the disc itself, they allow more heat to be dissipated, improving both cooling capacity and resistance to cracking from thermal shock. Unlike some other aftermarket brands, the venting vanes in discs are constructed exactly as the OE with the parting line in centre. Whilst this is more complicated and costly to cast, it provides much better braking balance and resistance to cracking.

Cross-drilled discs: In wet conditions, water acts as a cushion between the pad and disc, reducing friction and in turn stopping power. For this reason, our cross drilled discs feature additional axial holes on the friction plate. These holes help prevent a film of water forming for improved braking response in the wet. They also help to dissipate heat and any brake dust or gases that are generated when the pads come into contact with the discs. This helps to keep the pad surface both cool and clean and reduce thermal distortion, warping and brake fade.

High-carbon discs: By optimizing both carbon and silicon content, our high-carbon discs offer improved thermal behaviour, reducing the risk of thermal cracking under high-temperature loads, and allowing the discs to operate at a cooler temperature. Improved heat dissipation has the added benefit of also reducing distortion or warping, and in turn judder. And thanks to their high damping coefficient, they help reduce noise too.

Coated discs: Thanks to a special zinc-flake, silver Geomet coating across the entire surface, our coated brake discs offer both greater corrosion protection, compared with their oil-dipped or partially painted/coated equivalents, as well as improved aesthetics. The coating also stays in place longer, with salt spray resistance of up to 240 hours, versus less than 100 hours for many partially painted discs. And because they have no oil to clean off, they are easier and quicker to fit, saving valuable labour time and cost.

One-piece cast iron discs: Our one-piece cast iron discs offer an aftermarket alternative to the popular two-piece bi-metallic equivalent. Engineered from a single piece of high-carbon cast iron, instead of an aluminum hat and cast iron friction surface joined by metal rivets, they deliver the same standards of consistency, longevity and braking performance as the two-piece disc, but importantly are more cost-effective.

 Discs with bearings: Some rear wheel applications use brake discs with an integrated wheel hub and bearings. Since these are inherently difficult to replace, we offer a range with these safety critical components already pre-mounted.  This avoids damage to the bearing whilst removing it from the old disc, and the correct pressing in into the new. They also come with both toothed and magnetic ABS sensor rings integrated into the disc bearing, where fitted as OE, and the relevant fixing accessories. All for quick and accurate installation.

We like to think of this as our own discography; a range of finely-tuned, chart-topping discs, each with their own unique features and benefits, and each designed to perform like the OE. So, whether it’s coated, cross drilled or any combination of the above, you can install Delphi brake discs with complete confidence.


Fill yp your details to hear more from our experts and get the latest updates from Delphi.

I have read and accept the <a href="">Terms of Use</a> and <a href="">Privacy Policy</a>

I agree to receive personalised marketing emails.

I would like to be kept up to date with promotions/marketing/features/events.

You can change your mind at any time by clicking the unsubscribe link in the footer of any newsletter email you receive from us, or by contacting us at <a href="[email protected]">[email protected]</a>

A mechanic holding a diagnostic tool


Discover our extensive range of OE-level diagnostic and test equipment for quicker, more accurate servicing and repairs.

Two mechanics ready to start training


Choose from our expert-led, accredited training courses to enhance your skills and prepare you for the vehicles of tomorrow.

where to buy

Find out where to buy Delphi parts

where to repair

Find your nearest Service & Diesel Centres

Select your Region